WARNING: SWITCHEROO IS INTENDED FOR LIGHTING USAGE ONLY. PLUGGING ANYTHING BESIDES STANDARD LIGHTS (LAMPS ETC.) INTO SWITCHEROO MAY RESULT IN PERMANENT DAMAGE TO THE UNIT.
NOTICE: Switcheroo will not function connected to a dimming switch. It is against U.S. building code to connect a dimming switch to a standard outlet. Switcheroo will not function and may even fail permanently if connected to a dimmable outlet.
Electrical Rating: 120v AC, 8A, 60Hz, 960W
To use Switcheroo, set a Switcheroo to "Send" mode and pick a channel, then plug it into a switched outlet (or timer).
Then, set one or more other Switcheroos to "Receive" mode on the same channel and plug them into standard (non-switched) outlets. Note: You can have as many receiving units as you would like on each channel.
Plug lamps into configured Switcheroos as desired. The "Send" unit does not need to have a lamp plugged into it for the system to work.
Now, turn on your light switch and watch all of your lamps turn on together like magic!
Troubleshooting Guide
| Issue |
Resolution |
Receiving unit is ON when it should be OFF
|
- Change system to a different available channel
- Ensure that no other “Send” units are set to the same channel
|
Receiving unit is OFF when it should be ON
|
- Change system to a different available channel
- Ensure that the devices are not too far apart (generally about 100 feet)
- Ensure that the “Send” unit is receiving power (plugged in lamp is on)
- Confirm that no other interfering devices are nearby (cordless phones and other wireless devices)
|
Receiving unit is intermittently ON/OFF (blinking)
|
- Change system to a different available channel
- Ensure that the devices are not too far apart (generally about 100 feet)
- Confirm that no other interfering wireless devices are nearby
|
LIFETIME WARRANTY
Switcheroo is guaranteed for life. If you encounter any issues with Switcheroo at any time, use any of the contact methods on this site to request a replacement or refund. No questions asked.
If you encounter any issues with Switcheroo, please email support@switcheroo.com.
FCC ID: 2ANYY-SW1001LN, IC: 23584-SW1001LN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocated the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
